This is a guide to explain various useful variables in Userland component

Makefiles.  To distinguish these from the Makefile(s) that are part of each

component distribution, the latter will be referred to as native Makefiles.

The following are the basics that just about every Makefile should have.

* COMPONENT_NAME is typically a short name (e.g., vim).

* COMPONENT_VERSION is typically numbers separated by dots (e.g. 7.3).

* COMPONENT_SRC is where the archive is extracted.  A common value for this is

  "$(COMPONENT_NAME)-$(COMPONENT_VERSION)".

* COMPONENT_PROJECT_URL is the general web site for the component.

* COMPONENT_ARCHIVE is the base name of the archive to be downloaded.  A common

  value for this is "$(COMPONENT_SRC).tar.gz".

* COMPONENT_ARCHIVE_HASH is typically "sha256:" followed by the first output

  field of `sha256sum $(COMPONENT_ARCHIVE)`.

* COMPONENT_ARCHIVE_URL is where the archive can be downloaded from.  This is

  typically constructed from $(COMPONENT_PROJECT_URL) and $(COMPONENT_ARCHIVE).

* COMPONENT_SIG_URL is the URL where the PGP signature for $(COMPONENT_ARCHIVE)

  can be found.  This can be used in addition to the hash in

  $(COMPONENT_ARCHIVE_HASH) to verify the correctness of the archive.  If

  COMPONENT_SIG_URL is present, then COMPONENT_ARCHIVE_HASH needn't be, but its

  presence is strongly encouraged to ensure that the archive contents don't

  change silently.  If the signature results in a new key being added to

  tools/.gnupg/pubring.pgp, then as part of your code review, please show the

  diffs of the text version of the file by running

      gpg2 --homedir $WS/tools/.gnupg --fingerprint

  both before and after the change.  Note that when merging, because

  $WS/tools/.gnupg/pubring.gpg is a binary file, you will have to choose

  the parent or child version.  Pick one, then run:

	for cset in $(hg log -r 'parents()' -T '{node} '); do

		hg cat -r $cset $WS/tools/.gnupg/pubring.gpg | \

			gpg2 --homedir=$WS/tools/.gnupg --import;

	done

  before you 'hg commit' your merge.

* COMPONENT_BUGDB is the lower-case rendering of the BugDB cat/subcat.

These two are both initialized in make-rules/shared-macros.mk rather than any

component-level Makefile, but are frequently referenced from the latter.

* COMPONENT_DIR is the top-level directory of the given component in question.

* SOURCE_DIR is set to $(COMPONENT_DIR)/$(COMPONENT_SRC).

Additional pre/post configure, build, or install actions can be specified in

a component Makefile by setting them in one of the following macros.  None of

these have default values.  These are mostly used for miscellaneous set-up or

clean-up tweaks as their names suggest.

* COMPONENT_PRE_CONFIGURE_ACTION is used by several components to clone a

  source directory.

* COMPONENT_POST_CONFIGURE_ACTION

* COMPONENT_PRE_BUILD_ACTION

* COMPONENT_POST_BUILD_ACTION

* COMPONENT_PRE_INSTALL_ACTION

* COMPONENT_POST_INSTALL_ACTION

* COMPONENT_PRE_TEST_ACTION

* COMPONENT_POST_TEST_ACTION

If component specific make targets need to be used for build or install or

test, they can be specified via the following.

* COMPONENT_BUILD_TARGETS is not usually set because the default target of most

  open source software is the equivalent of a 'build' target.  This needs to be

  set when building the software requires a different target than the default.

  You should not override make macros here, but in COMPONENT_BUILD_ARGS.

* COMPONENT_INSTALL_TARGETS has a default value of "install".  Very few

  components need to alter this.

* COMPONENT_TEST_TARGETS has a default value of "check".  Several components

  need to set this to "test".

* COMPONENT_BUILD_ARGS is probably the mostly useful variable here for solving

  subtle build issues.  When you need to override a MACRO set in the native

  Makefile of a component, do so by adding something like:

     COMPONENT_BUILD_ARGS += MKDIR="$(MKDIR)"

  Quoting is often important because values with white-space can be split up,

  yielding the wrong results.

* COMPONENT_BUILD_ENV is for when you just need to override things in the

  calling environment, like PATH.

* COMPONENT_INSTALL_ARGS is mainly used for altering target directories.

* COMPONENT_INSTALL_ENV is mainly used for altering target directories.

* COMPONENT_PUBLISH_ENV is so far only used to work around Python issues when

  used by "pkgdepend generate", though the variable may be extended in the

  future for general "gmake publish" usage.

* COMPONENT_TEST_ARGS is little used.

* COMPONENT_TEST_ENV is mainly used for altering PATH and friends.

If your component needs to do some kind of cleanup after a "gmake test" run,

such as kill processes after doing a "gmake test" run, then this can be done

by setting COMPONENT_TEST_CLEANUP.

If you have created master test results file(s) for your component in the

COMPONENT_TEST_RESULTS_DIR directory, then in order to successfully compare

your test results against that master results file, you might need to

normalize some of the test output lines. This is done via a set of regular

expressions that are applied to the test results. There are some global

default ones in the COMPONENT_TEST_TRANSFORMS definition in shared-macros.mk,

but your component Makefile might have to += some more for specific transforms

that need to be applied to the test output for just this component.

* SKIP_TEST_AT_TOP_LEVEL inclusion of this variable in a component Makefile

  will cause that component's tests to be skipped when running "gmake test"

  at the top level.  It's often used for excluding long-running tests 

  that may slow down comprehensive component testing.  

* COMPONENT_POST_UNPACK_ACTION is for making minor alterations to the unpacked

  source directory before any patching has taken place.  It should almost never

  be used.

* COMPONENT_PREP_ACTION is used to make alterations to the unpacked and patched

  source.  It should be used with care.

* CONFIGURE_DEFAULT_DIRS should be "yes" or "no".  A value of "yes" (the

  default) will trigger the following being passed to CONFIGURE_OPTIONS as

  parameters to corresponding options.

  * CONFIGURE_BINDIR is the value for the --bindir= option.

  * CONFIGURE_LIBDIR is the value for the --libdir= option.

  * CONFIGURE_MANDIR is the value for the --mandir= option.

  * CONFIGURE_SBINDIR is the value for the --sbindir= option.

* CONFIGURE_ENV is mainly used for passing CFLAGS and other common Makefile

  variables to configure.  When should this be used as opposed to

  CONFIGURE_OPTIONS and COMPONENT_BUILD_{ARGS,ENV}?  In general, you want

  to tell configure how to build the software using CONFIGURE_OPTIONS.  But

  sometimes you need to pass values in via the calling environment.  On rare

  occasions, you still need to do things like override MACRO settings in the

  generated Makefiles with COMPONENT_BUILD_ARGS.

* CONFIGURE_LOCALEDIR is a cousin of the other *DIR variables above, but

  rarely used and hence not triggered by CONFIGURE_DEFAULT_DIRS.

* CONFIGURE_OPTIONS is extremely useful, possibly our most used "add-on"

  variable, for passing various options to configure.  These tend to vary per

  component, but --enable-foo and --disable-foo for various values of foo are

  quite common.

* CONFIGURE_PREFIX is the prefix for the various *DIR variables above.  Its

  default is "/usr"; set it if some other value (e.g., "/usr/gnu") is needed.

* CONFIGURE_SCRIPT should be set if the default "$(SOURCE_DIR)/configure" is

  unsuitable for whatever reason.

* studio_OPT has a default value of "-xO4".  Occasional bugs in the optimizer

  have been found which have required altering this to "-xO3".  There are also

  studio_OPT.$(MACH).$(BITS) versions of this available if greater specificity

  is needed.

* TPNO is the Third Party number (i.e., a numeric value): the License

  Technology from the Product Lifecycle Suite tool.  This should be used

  in the common case when there is just one TPNO for a component.  We

  recommend that this be near the top of any Makefile, just below the

  various COMPONENT_foo definitions.

* TPNO_foo is for the rare case (~3% of components) when a component has

  more than one TPNO.  Each one should have a separate short but descriptive

  name substituted for "foo".  This likewise should be near the top of any

  Makefile, just below the various COMPONENT_foo definitions, and it must

  also be before the inclusion of ips.mk .

---

Now switching from explaining the function of specific variables to a more

general discussion about how to use them to solve problems.  One method that

has served time and again is adding a level of indirection.  For example,

when Python 3 came along, we decided to build it 64-bit only, which meant

its various modules also needed to be built 64-bit only.  But many of them

had BUILD_32_and_64 in their native Makefile.  So how to tweak that macro

to do one thing for Python 2.x but another for 3.x?  JBeck spent an entire

day trying various combinations that seemed right, but none of them worked.

Then Norm pointed out that changing PYTHON_VERSIONS from "3.4 2.7 2.6" to

$(PYTHON3_VERSIONS) and $(PYTHON2_VERSIONS) which in turn were "3.4" and

"2.7 2.6" would do the trick.  I.e., adding a level of indirection solved

the problem, as it allowed $(PYTHON_VERSIONS) to be used to specify 64-bit

macros but $(PYTHON2_VERSIONS) to specify 32-bit macros.  There are many

other places where constructs like this are used.